
Three ways to set up a work ute
When a ute is a tool of trade, the factory tub is rarely the best use of the space. Most of the utes that come through our Keysborough workshop leave with one of three setups, and the right one depends on what you carry and how often you reach for it.
- A ute tray is a flat deck, with or without drop sides. It suits bulky or dirty loads such as pallets, timber, soil and machinery, and anything loaded by forklift.
- A tray with a canopy keeps the flat deck but adds a lockable box over part or all of it. It suits trades that carry both materials and tools.
- A service body replaces the tray with lockable side compartments, shelves and drawers. It suits field technicians, council crews and anyone who works out of the vehicle all day and needs every tool in the same place.
Steel or aluminium ute tray
This is the question we are asked most, and there is no single right answer.
Aluminium is much lighter than steel, so more of the ute's payload is left for your load. It does not rust, which matters near the coast and for anyone carrying wet or corrosive materials. A custom aluminium tray usually costs more to build than a steel one of the same size.
Steel is heavier, stronger and stiffer, and it stands up well to point loads and rough treatment, such as pallets dropped by a forklift or a deck that is used as a workbench. It needs galvanising or a good paint system to keep rust away, and that finish needs looking after.
As a rule of thumb, choose aluminium when payload is tight or the ute works in wet conditions, and choose steel when the deck takes heavy knocks and weight is not your limit. Our guide to aluminium and steel truck bodies covers the same choice for larger trucks.
Service body, or tray and canopy
A service body gives you the most organised storage, with compartments you open from the side while standing on the ground. The cost is that the centre of the vehicle is no longer an open deck, so large or awkward items are harder to carry.
A tray and canopy is more flexible. A part canopy leaves deck space behind it for materials, and some canopies lift off when you need the whole tray. If your work changes from week to week, this is usually the safer choice. If you carry the same tools and parts every day, a service body will save you time on every job.
Payload: the number that decides everything
Every ute has a gross vehicle mass, or GVM, which is the most it may legally weigh when loaded, including the driver, passengers, fuel, the body and everything in it. The tray, canopy, toolboxes, racks and water tank all come out of that allowance before you load a single tool.
It is common for a fully fitted work ute to be close to its limit before the day's materials go on. We ask what you carry so that we can choose materials and a layout that leave you a useful payload. If the sums do not work, it is better to know before the body is built, when the answer might be a lighter material, a smaller canopy or a different vehicle.
What needs engineering sign-off in Victoria
Victoria's vehicle standards for light vehicles, up to 4.5 tonnes GVM, list the modifications an owner can make without approval. A body that is outside that list, or outside what the vehicle's manufacturer offers as standard, can need an approval certificate from a signatory under the Vehicle Assessment Signatory Scheme, known as VASS. The owner of the vehicle is responsible for making sure it complies.
There are also limits on how far a body can extend behind the rear axle and how wide the vehicle can be, so a longer or wider tray is not always possible. We build each body to suit the vehicle's dimensions and the manufacturer's body building guide. Where a job needs sign-off, we work with registered engineers and certifiers and include it in your quote.
Options worth thinking about early
- Drop sides and a tailgate, or a flat deck with tie-down rails.
- The headboard height, and whether it needs a mesh or a window guard.
- Ladder racks, and how long the ladders, pipe or conduit are.
- Under-tray toolboxes and a pull-out drawer under the deck.
- Where the spare wheel will go once the tub is off.
- A water tank with a tap and a soap holder.
- Where the tail lights, number plate, fuel filler, reversing camera and parking sensors will be moved to.
- Paint or powder coat to match the vehicle or your business colours.
These are far easier and cheaper to include in the first build than to add afterwards.
Thinking ahead to your next ute
A well built tray or service body often outlasts the ute underneath it. If you replace your vehicles every few years, tell us, because a body can be built so that it is practical to move to the next vehicle of a similar size. We also refit existing bodies onto new utes, and we repair trays and service bodies that have been damaged.
Getting a quote for a ute tray or service body
VN Truck Bodies builds ute trays, service bodies and canopies in Melbourne to order, for one ute or a whole fleet. Tell us the make and model, what you carry and how you work, and we will recommend a setup that suits. You can call us on 0447 452 222 or come and see us at 17 Cambria Road, Keysborough VIC 3173.